Add support for Embedded Planet target Atlas

targets/TARGET_NORDIC/TARGET_NRF5x/TARGET_NRF52/TARGET_MCU_NRF52840/TARGET_EP_ATLAS/ONBOARD_TELIT_ME310.cpp

@@ -0,0 +1,169 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2019 ARM Limited
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "gpio_api.h"
+#include "platform/mbed_thread.h"
+#include "PinNames.h"
+#include "BufferedSerial.h"
+#include "ONBOARD_TELIT_ME310.h"
+#include "ThisThread.h"
+#include "CellularLog.h"
+
+
+using namespace mbed;
+
+ONBOARD_TELIT_ME310::ONBOARD_TELIT_ME310(FileHandle *fh) : TELIT_ME310(fh, P0_31, true)
+{
+}
+
+nsapi_error_t ONBOARD_TELIT_ME310::hard_power_on()
+{
+    onboard_modem_init();
+    return NSAPI_ERROR_OK;
+}
+
+nsapi_error_t ONBOARD_TELIT_ME310::hard_power_off()
+{
+    onboard_modem_deinit();
+    return NSAPI_ERROR_OK;
+}
+
+nsapi_error_t ONBOARD_TELIT_ME310::soft_power_on()
+{
+    onboard_modem_power_up();
+    // From Telit_xE310 Global form factor App note: It is mandatory to avoid sending data to the serial ports during the first 200ms of the module start-up.
+    rtos::ThisThread::sleep_for(200);
+    return NSAPI_ERROR_OK;
+}
+
+nsapi_error_t ONBOARD_TELIT_ME310::soft_power_off()
+{
+    onboard_modem_power_down();
+    return NSAPI_ERROR_OK;
+}
+
+nsapi_error_t ONBOARD_TELIT_ME310::init()
+{
+    nsapi_error_t err = AT_CellularDevice::init();
+    if (err != NSAPI_ERROR_OK) {
+        return err;
+    }
+    _at.lock();
+#if DEVICE_SERIAL_FC
+    _at.at_cmd_discard("&K3;&C1;&D0", "");
+#else
+    _at.at_cmd_discard("&K0;&C1;&D0", "");
+#endif
+
+    // AT#QSS=1
+    // Enable the Query SIM Status unsolicited indication in the ME. The format of the
+    // unsolicited indication is the following:
+    // #QSS: <status>
+    // The ME informs at
+    // every SIM status change through the basic unsolicited indication where <status> range is 0...1
+    // <status> values:
+    // - 0: SIM not inserted
+    // - 1: SIM inserted
+    _at.at_cmd_discard("#QSS", "=1");
+
+    // AT#PSNT=1
+    // Set command enables unsolicited result code for packet service network type (PSNT)
+    // having the following format:
+    // #PSNT:<nt>
+    // <nt> values:
+    // - 0: GPRS network
+    // - 4: LTE network
+    // - 5: unknown or not registered
+    _at.at_cmd_discard("#PSNT", "=1");
+
+    // AT+CMER=2
+    // Set command enables sending of unsolicited result codes from TA to TE in the case of
+    // indicator state changes.
+    // Current setting: buffer +CIEV Unsolicited Result Codes in the TA when TA-TE link is
+    // reserved (e.g. on-line data mode) and flush them to the TE after
+    // reservation; otherwise forward them directly to the TE
+    _at.at_cmd_discard("+CMER", "=2");
+
+    // AT+CMEE=2
+    // Set command disables the use of result code +CME ERROR: <err> as an indication of an
+    // error relating to the +Cxxx command issued. When enabled, device related errors cause the +CME
+    // ERROR: <err> final result code instead of the default ERROR final result code. ERROR is returned
+    // normally when the error message is related to syntax, invalid parameters or DTE functionality.
+    // Current setting: enable and use verbose <err> values
+    _at.at_cmd_discard("+CMEE", "=2");
+
+    // AT#PORTCFG=0
+    // Set command allows to connect Service Access Points to the external physical ports giving a great
+    // flexibility. Examples of Service Access Points: AT Parser Instance #1, #2, #3, etc..
+    _at.at_cmd_discard("#PORTCFG", "=", "%d", EP_ATLAS_PORT_CONFIGURATION_VARIANT);
+
+    // AT&W&P
+    // - AT&W: Execution command stores on profile <n> the complete configuration of the device. If
+    //         parameter is omitted, the command has the same behavior of AT&W0.
+    // - AT&P: Execution command defines which full profile will be loaded at startup. If parameter
+    //         is omitted, the command has the same behavior as AT&P0
+    _at.at_cmd_discard("&W&P", "");
+
+    return _at.unlock_return_error();
+}
+
+void ONBOARD_TELIT_ME310::press_power_button(int time_ms)
+{
+    gpio_t gpio_CELL_ON_OFF;
+    gpio_init_out_ex(&gpio_CELL_ON_OFF, P0_31, 1);
+    gpio_write(&gpio_CELL_ON_OFF, 1);
+}
+
+void ONBOARD_TELIT_ME310::onboard_modem_init()
+{
+}
+
+void ONBOARD_TELIT_ME310::onboard_modem_deinit()
+{
+}
+
+void ONBOARD_TELIT_ME310::onboard_modem_power_up()
+{
+    /* keep the power line low for 5 seconds */
+    press_power_button(6000);
+    /* give modem a little time to respond */
+}
+
+void ONBOARD_TELIT_ME310::onboard_modem_power_down()
+{
+    gpio_t gpio;
+
+    gpio_init_out_ex(&gpio, P0_31, 0);
+    /* keep the power line low for more than 3 seconds.
+     * If 3G_ON_OFF pin is kept low for more than a second, a controlled disconnect and shutdown takes
+     * place, Due to the network disconnect, shut-off can take up to 30 seconds. However, we wait for 10
+     * seconds only   */
+    thread_sleep_for(10 * 1000);
+}
+
+CellularDevice *CellularDevice::get_target_default_instance()
+{
+    static BufferedSerial serial(P1_2, P1_1, 115200);
+#if DEVICE_SERIAL_FC
+    if (P0_11 != NC && P1_8 != NC) {
+        tr_debug("Modem flow control: RTS %d CTS %d", P0_11, P1_8);
+        serial.set_flow_control(SerialBase::RTSCTS, P0_11, P1_8);
+    }
+#endif
+    static ONBOARD_TELIT_ME310 device(&serial);
+    return &device;
+}

targets/TARGET_NORDIC/TARGET_NRF5x/TARGET_NRF52/TARGET_MCU_NRF52840/TARGET_EP_ATLAS/ONBOARD_TELIT_ME310.h

@@ -0,0 +1,49 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2019 ARM Limited
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef ONBOARD_TELIT_ME310_
+#define ONBOARD_TELIT_ME310_
+
+#include "TELIT_ME310.h"
+
+namespace mbed {
+
+class ONBOARD_TELIT_ME310 : public TELIT_ME310 {
+public:
+    ONBOARD_TELIT_ME310(FileHandle *fh);
+
+    virtual nsapi_error_t init();
+    virtual nsapi_error_t hard_power_on();
+    virtual nsapi_error_t hard_power_off();
+    virtual nsapi_error_t soft_power_on();
+    virtual nsapi_error_t soft_power_off();
+
+private:
+    void press_power_button(int time_ms);
+
+    void onboard_modem_init();
+
+    void onboard_modem_deinit();
+
+    void onboard_modem_power_up();
+
+    void onboard_modem_power_down();
+};
+
+} // namespace mbed
+
+#endif // ONBOARD_TELIT_ME310_