V4.5 rc3/apq8096 wip

Documentation/devicetree/bindings/clock/qcom,rpmcc.txt

@@ -0,0 +1,37 @@
+Qualcomm RPM Clock Controller Binding
+------------------------------------------------
+The RPM is a dedicated hardware engine for managing the shared
+SoC resources in order to keep the lowest power profile. It
+communicates with other hardware subsystems via shared memory
+and accepts clock requests, aggregates the requests and turns
+the clocks on/off or scales them on demand.
+
+Required properties :
+- compatible : shall contain only one of the following. The generic
+               compatible "qcom,rpmcc" should be also included.
+
+			"qcom,rpmcc-msm8916", "qcom,rpmcc"
+			"qcom,rpmcc-apq8064", "qcom,rpmcc"
+
+- #clock-cells : shall contain 1
+
+Example:
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <0 168 1>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests {
+				compatible = "qcom,rpm-msm8916";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: qcom,rpmcc {
+					compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
+					#clock-cells = <1>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/display/msm/hdmi.txt

@@ -11,13 +11,15 @@ Required properties:
 - reg: Physical base address and length of the controller's registers
 - reg-names: "core_physical"
 - interrupts: The interrupt signal from the hdmi block.
+- power-domains: Should be <&mmcc MDSS_GDSC>.
 - clocks: device clocks
   See ../clocks/clock-bindings.txt for details.
 - qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
 - qcom,hdmi-tx-ddc-data-gpio: ddc data pin
 - qcom,hdmi-tx-hpd-gpio: hpd pin
 - core-vdda-supply: phandle to supply regulator
 - hdmi-mux-supply: phandle to mux regulator
+- qcom,dsi-phy: phandle to HDMI PHY device node
 
 Optional properties:
 - qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
@@ -27,6 +29,27 @@ Optional properties:
 - pinctrl-0: the default pinctrl state (active)
 - pinctrl-1: the "sleep" pinctrl state
 
+HDMI PHY:
+Required properties:
+- compatible: Could be the following
+  * "qcom,hdmi-phy-8x60"
+  * "qcom,hdmi-phy-8960"
+  * "qcom,hdmi-phy-8x74"
+  * "qcom,hdmi-phy-8996"
+- reg: Physical base address and length of the registers of the PHY sub blocks.
+- reg-names: The names of register regions. The following regions are required:
+  * "hdmi_pll"
+  * "hdmi_phy"
+  For HDMI PHY on msm8996, these additional register regions are required:
+    * "hdmi_tx_l0"
+    * "hdmi_tx_l1"
+    * "hdmi_tx_l3"
+    * "hdmi_tx_l4"
+- power-domains: Should be <&mmcc MDSS_GDSC>.
+- clocks: device clocks
+  See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
+- core-vdda-supply: phandle to vdda regulator device node
+
 Example:
 
 / {
@@ -35,7 +58,7 @@ Example:
 	hdmi: qcom,hdmi-tx-8960@4a00000 {
 		compatible = "qcom,hdmi-tx-8960";
 		reg-names = "core_physical";
-		reg = <0x04a00000 0x1000>;
+		reg = <0x04a00000 0x2f0>;
 		interrupts = <GIC_SPI 79 0>;
 		power-domains = <&mmcc MDSS_GDSC>;
 		clock-names =
@@ -54,5 +77,19 @@ Example:
 		pinctrl-names = "default", "sleep";
 		pinctrl-0 = <&hpd_active  &ddc_active  &cec_active>;
 		pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>;
+
+		qcom,hdmi-phy = <&hdmi_phy>;
+	};
+
+	hdmi_phy: qcom,hdmi-phy-8960@4a00400 {
+		compatible = "qcom,hdmi-phy-8960";
+		reg-names = "hdmi_phy",
+			    "hdmi_pll";
+		reg = <0x4a00400 0x60>,
+		      <0x4a00500 0x100>;
+		power-domains = <&mmcc MDSS_GDSC>;
+		clock-names = "slave_iface_clk";
+		clocks = <&mmcc HDMI_S_AHB_CLK>;
+		core-vdda-supply = <&pm8921_hdmi_mvs>;
 	};
 };

arch/arm64/boot/dts/qcom/Makefile

@@ -1,4 +1,7 @@
-dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb msm8916-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-dragonboard.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/qcom/apq8096-dragonboard.dts

@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "apq8096-dragonboard.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. APQ 8096 DragonBoard";
+	compatible = "qcom,apq8096-dragonboard";
+	qcom,board-id = <10 0>;
+};

arch/arm64/boot/dts/qcom/apq8096-dragonboard.dtsi

@@ -0,0 +1,44 @@
+/*
+ * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8996.dtsi"
+
+/ {
+	aliases {
+		serial0 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		serial@75b0000 {
+			status = "okay";
+		};
+
+		qcom,hdmi_phy@9a0600 {
+			status = "okay";
+
+			vddio-supply = <&pm8994_l12>;
+			vcca-supply = <&pm8994_l28>;
+		};
+
+		qcom,hdmi_tx@9a0000 {
+			status = "okay";
+
+			core-vdda-supply = <&pm8994_l12>;
+			core-vcc-supply = <&pm8994_s4>;
+		};
+	};
+};

arch/arm64/boot/dts/qcom/msm8996-mtp.dts

@@ -0,0 +1,21 @@
+/*
+ * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "msm8996-mtp.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. MSM 8996 MTP";
+	compatible = "qcom,msm8996-mtp";
+};

arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi

@@ -0,0 +1,30 @@
+/*
+ * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8996.dtsi"
+
+/ {
+	aliases {
+		serial0 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		serial@75b0000 {
+			status = "okay";
+		};
+	};
+};